- #Usb cdc modem device driver for china mobile how to#
- #Usb cdc modem device driver for china mobile drivers#
- #Usb cdc modem device driver for china mobile driver#
- #Usb cdc modem device driver for china mobile software#
The nature of, and the requirement for, the virtual Ethernet layer is somewhat application dependent. For more information see the MCCI USB DataPump Network Drivers.įigure 4.
#Usb cdc modem device driver for china mobile software#
Windows Software Architecture - Networkingįirmware Architecture for USB Networking DevicesĪ matching firmware architecture for a USB device implementation is shown in Figure 4. When necessary, we substitute a different miniport layer that is tailored for the NDIS version used by the target version of Windows but the USB layer doesn’t need to change.įigure 3. With this architecture, MCCI can provide identical code at the USB layer in a way that is independent of NDIS version. Different versions of Windows use different versions of NDIS.
#Usb cdc modem device driver for china mobile driver#
For architectural reasons, MCCI uses a two part driver this simplifies management, and separates the portion of the driver that’s responsible for the NDIS interface from the portion of the driver that’s responsible for the USB network protocol. MCCI Network Driver Architecture for Windowsįigure 3 shows the driver architecture for Windows. Frequently, however, this extra Ethernet address can be eliminated, because of the point-to-point nature of the link, especially if (as in cable modems) another NIC already has an Ethernet address assigned the cable modem NIC address can also be used on the virtual Ethernet. One would be associated with the NIC that was previously in the host and one is associated with the NIC that was previously in the device. Notice that the presence of two NICs implies that there are two Ethernet addresses embedded in the USB device. If the NIC has been integrated into the target device (for example, as in a LTE modem or a cable modem), the software on the PC is the same, but the physical Ethernet segment is replaced by a software “virtual” Ethernet segment.Īlthough the following discussion focuses on CDC Ethernet as the transport protocol, it is equally true for CDC Network Control Model (NCM) - NCM is faster, but the architecture is the same.įigure 1 compares the USB remote NICs to local NIC architectures.įigure 2 illustrates the virtual Ethernet architecture used in USB cable modems and home networking/SOHO routing applications. If a USB-to-Ethernet bridge is being used, the USB bus, an Ethernet NIC, and a physical Ethernet segment will all be present.
In this case, the Ethernet Network Interface Controller (NIC) is connected to the user’s computer using USB.
#Usb cdc modem device driver for china mobile drivers#
The easiest way to understand the architecture of USB networking drivers is to start by considering a USB to Ethernet adapter. Off-the-shelf eval drivers are available for Windows platforms. MCCI® offers complete driver and firmware solutions for USB networking. Notable applications include LTE modems, cable modems and ADSL. I believe 'option' driver missing in above list is the problem.USB is a popular way to connect broadband networking devices to consumer PCs. But it is not detected as a ttyUSB0,ttyUSB1 etc. qmi_wwan and cdc-wdm modems are detected which is good news. Quectel driver userguide tells that I should be able to see 'option' as a usb driver. Now I replace these new kernal modules onto my linux board and reboot. While generating new option.ko, qcserial.ko, usb_wwan.ko, I used KDIR = compiled/kernal/path.
#Usb cdc modem device driver for china mobile how to#
I learnt how to cross-compile these files by downloading my kernal source files on to another ubuntu PC.
My linux board has little memory and didnot have linux-headers nor source on the board memory system (i.e no build folder exists in /lib/modules/4.9.11-g09a125b5724d/ Quectel provides c files and Makefile of these drivers with necessary modifications for my kernal version of linux 4.9.11 (Debian buster running). Modification mainly has addition of new VID and PID details of the modem for usb-serial to detect. Modem's document tells that we need to modify the linux driver files - option.c, qcserial.c, usb_wwan.c. I am using TS7970 Linux board and trying to enable LTE modem using Quectel LTE EG25-G Mini PCIe.
0 kommentar(er)
